Why is your router’s Ethernet interface called Ethernet0/0 on one router but Ethernet 3/0 on another router? Where do these names come from? This article will explain how Cisco router interfaces get their names.
Windows Server 2012 is now available!
It offers businesses and service providers a scalable, dynamic, and multitenant-aware cloud-optimized infrastructure.
Windows Server 2012 helps organizations connect securely across premises and helps IT Professionals to respond to business needs faster and more efficiently.
Where do Router Interfaces get their names?
Router interfaces get their names when the router boots. A “device discovery” takes place and the names of the interfaces are generated based on a predicable method. On fixed interface routers (like the older 2500 series routers) the interfaces will always be the same. However, on newer routers like 2600, 3600, 3700, and 2800 series routers, interfaces can be modular. That means that the interfaces are cards (modules) that can be “plugged into” the router in different slots. Some of these interfaces are on WAN interface cards (WIC) and some are on Network Modules (NM). Other router interfaces will be built right onto the router. The newer model routers have different names for some of these slots like enhanced network modules (NME) and high-speed WIC (HWIC). However, for the purposes of naming the interfaces, the effect is the same.
Interface Naming Conventions
Cisco router interfaces are named with the following convention:
The media type is Ethernet, FastEthernet, GigabitEthernet, Serial, Token-ring, or other media types. You must keep in mind that a 10Mb Ethernet interface is the only kind of Ethernet interface called Ethernet. A 100Mb Ethernet interface is called a FastEthernet interface and a 1000Mb Ethernet interface is called a GigabitEthernet interface.
Now let’s talk about the “slot#/port#” designation. On the old 2500 series routers, they had fixed ports so there was no slot numbers. Thus, if a 2500 series router had two Ethernet interfaces, they were called Ethernet0 and Ethernet1. It is important to point out that Cisco slots and ports always start with zero first, then one.
On the newer model routers with slots, any interface built onto the router (a fixed port) is considered to be in slot 0 (zero). This is even true for WAN interface cards (WIC) slots that are on the router. Any WIC installed in a router is in slot 0. So, the first WIC installed in the router will always be WIC 0, even if it is in slot 1. This can be confusing sometimes. So if Slot 0 has a 2 port serial WIC and Slot 1 had a BRI interface, you have Serial 0/0, Serial 0/1, and BRI0/0.
Say that you have a Cisco 2610 router. If you put a Serial WIC card in slot zero (called W0 on the router), that module would be called Serial0/0. If there was a two port Serial WIC card in the other slot (slot W1), it would be called Serial0/1 and Serial0/2.
Say that you had a Cisco 3640 router. That router has 4 NM slots and no built in network interfaces. The network module numbering on a 3640 starts with zero and goes to three. This number starts on the bottom right of the router (there are four slots, two and two, each two on top of the other two) with zero. So, the bottom right slot is slot zero. The bottom left slot is one, the top right slot is two, and the top left slot is three. If you put a module with two WIC cards in the top right slot, your WIC cards would be called Ethernet2/0 and Serial2/0.
Here is a picture showing this layout:
Picture courtesy of Cisco.com
The show ip interface brief command is the most useful command to see what interfaces are on the router and what their names are. Here is an example:
This command output is from a Cisco 2611 router. It has two built in Ethernet interfaces and two WIC slots. In the first WIC slot is a single port Serial module. In the second WIC slot is a two port serial module. You can see how the naming we have been talking about applies to these modules.
If I were to turn off the router, remove the two port serial interface, and reboot the router, you would see that the configuration for those modules has disappeared. Thus, if I were to save that configuration, turn off the router, replace the two port serial module with a good module, and reload the router. The configuration for those two serial modules would be lost. This is another important reason to always have a good backup copy of your Cisco IOS configuration.
What you need to take home from this article is:
The network interface naming depends on the type of router you have and what slots are on that router.
Interface numbering starts at zero and goes up.
Router network modules are named zero and go up, starting with the bottom right slot.
Be familiar with the models of routers you use and how their slots are laid out.
All built in interfaces on a modular router and all WIC cards are considered to be in slot 0.
When in doubt, look at the router and how its slots are labeled and do a show ip interface brief to see what slots were found. Preferably, you should match up the physical slots and interfaces with the named interfaces before making any changes on that router.
For more information, see Cisco’s document on Understanding Interface Numbering and Cisco IOS Basics